16 Tower w/ACD Test Plan (pre-FSW)
Rev. 11/8/05 L.Wai
Sub-Series	Test	Purpose	Time (hr)	Totals	Time (hr)
ACD Integ.	safe-to-mate	LAT interface safe-to-mate	8	ACD Integ.:	8
LAT CPT	AEM/ACD Clock Phase Bit Test	ACD/DAQ clock	4
LAT CPT	GASU register test	Check for GASU errors	4
LAT CPT	register test - redundant GASU/PDU	Check for TEM errors	4
LAT CPT	register test - primary GASU/PDU	Check for TEM errors	4
LAT CPT	ACD CPT	Baseline LAT CPT	16
LAT CPT	LAT CPT - TKR Section*	Baseline LAT CPT	2
LAT CPT	LAT CPT - CAL Section*	Baseline LAT CPT	2	LAT CPT:	36
Trigger	ACD Channel Uniformity	Check ROI and CNO arrival times with CI	4
Trigger	ACD Hitmap Latching	Optimize hitmap latch delay and stretch	4
Trigger	ACD CI Circuit Retriggering**	Verify ACD CI circuit behavior (NCR706)	0
Trigger	CAL Channel Uniformity	CAL-LO and CAL-HI arrival times with CI	2
Trigger	CAL FLE Muon Scan	FLE threshold and trigger mask for timing	6
Trigger	ACD TREQ with ext trigger**	ACD ROI arrival times w/ muon tel. trig.	0
Trigger	ACD Trigger Rate Test	Optimize ROI trig. for CAL/TKR TREQ test	8
Trigger	CAL, TKR TREQ Alignment	CAL-LO, TKR arrival times w/ ROI trig.	8
Trigger	ACD TREQ with TKR trigger	ACD ROI arrival times w/ TKR trig.	8
Trigger	ACD, CAL, TKR TACK Scan	Optimize TACK for all three subsystems	8
Trigger	Trigger Efficiency***	Trig eff. study for all three subsystems	0
Trigger	ACD Veto Mode Run***	Cosmics run w/ CAL-LO || (TKR && !ROI)	0	TRIGGER:	48
CALIB	CalibDac (CAL discriminator scans)	CAL thresholds calibration	5
CALIB	CalibGen (CAL charge injection scan)	CAL ADC calibration	3
CALIB	MuTrig  (CAL muon data)****	CAL energy calibration	2
CALIB	TE601 (TKR threshold scan)	TKR threshold calibration	4
CALIB	TE602 (TKR full range charge inj. scan)	TKR TOT calibration	4
CALIB	TE604 (TKR charge scan at threshold)	TKR threshold dispersion	4	CALIB:	22
TKR perf.	TE702 (TKR trigger jitter)	tracker performance test	4	TKR Perf:	4
SVAC	e2e B-2, B-10, B-13 (1 minute ea.)	Configuration Validation	2
SVAC	e2e B-13 (15 min)	SVAC data collection	2
SVAC	e2e B-10 (15 hours)	SVAC data collection	20
SVAC	e2e B-2 (4 hours)	SVAC data collection	6	SVAC:	30
	* data analysis may be deferred			TOTAL:	148
	** these tests may be deferred
	*** these tests may be replaced by equivalent SVAC phase 2 runs
	**** this test may be reduced in scope
Sign-off:	I&T Management	_____________________
	Systems Engineering	_____________________
	Quality Assurance	_____________________